PhoenixCoat™ Paint Revival Serum

PhoenixCoat™ is designed to make the clear coat of older, faded vehicles look 80 to 90% better. For best results, we recommend using this product as follows:   

• On the exterior of a vehicle only   
• On panels that are between 50 to 90°F   
• In environments of less than 90% humidity   
• In a well-ventilated area   
• While wearing gloves / masks / PPE   
• Keeping the vehicle dry for 24 hours after applying   
• Practice on a small panel first before doing the entire vehicle   

1.  PREP / WASH

• Cleaning and prep are key. Wash the area you're going to apply the product on with water and/or detailing spray.   
• If your vehicle's clear coat is peeling or flaking, lightly sand the peeling edges with fine (wet) sandpaper to level and smooth them out, so the surface is even before application. Sand gently in one direction and avoid going too deep. After sanding, rinse away all sanding dust and let the area dry completely.   
• Make sure the area is dry before application.   
• Practice on a small section of a panel before applying to the rest of the vehicle.   

2. APPLICATION

• Shake the PhoenixCoat™ bottle with the cap on.   
• Remove the seal beneath the cap.   
• Apply the serum to a folded shop towel or micro applicator. Be sure to put enough product on the towel to keep a wet edge throughout your entire panel. We recommend keeping the bottle handy. If your towel starts to get dry during application, apply a bit more PhoenixCoat™ to keep the towel wet.   
• Start at the top corner of the panel to allow excess serum to drip down the panel.   
• Hold the towel with a flat hand. Using light pressure, glide edge to edge across the panel. Go back and forth, overlapping the edges of your lines. Evenly disperse the product across the panel. If you miss a spot in the first 2 to 3 minutes, take a full, gentle line back through that area. Make sure you don't miss any spots, but don't go over a spot more than needed.   
• You will have a 2 to 3 minute window to work with. DO NOT go back over an area after that time period.   

Please note: if a significant mistake is made during application and you need to remove the coating, stripping it is much easier within 15 minutes of initial application. Within that 15-minute window, we recommend scrubbing the coating with Wax and Grease Remover. If you need to remove the coating after it has already cured, you will need to wet sand / heavy cut with a rotary or elbow grease using a heavy solvent. This is a long-lasting coating.

3. CURING / AFTER-CARE

• The application needs 24 hours to cure. Do NOT touch the area or let it get wet for at least 24 hours after application. Once cured, you'll have a long-lasting coating. Note that the more product you apply, the longer it will take to cure.   
• You can hand wash the vehicle 48 hours after application. We recommend you DO NOT take the vehicle through an automatic car wash after application. Auto washes are already known to scratch regular clear coat, so they can do the same to this coating.   

COMMON MISTAKES   

Streak Lines   

This can be caused by too many overlapping passes on the same area in direct sunlight, or applying in a random, obscure motion. Make sure you go in straight lines and try not to go over an area more than once. Be sure to keep a wet edge on your application towel.   

Rainbowing or Excessive Low Spots

The main cause is NOT USING ENOUGH PRODUCT. Be sure you have enough on your towel. Using too much or uneven pressure is another issue to avoid. Apply with light, even pressure throughout the panel.   

Fish Eyes / Solvent Pops

To avoid pops in the finish, make sure not to let the area get wet, wait 24 hours, and let the first layer cure for 24 hours before applying any additional layers.   

Dirt Nibs

To avoid specks of dirt in the coating, the cleaning/prep step is KEY. If you have dirt in your finished result, you likely didn't prep well enough.   

📦 Shipping Details

• Orders are processed within 1-2 business days.
• Estimated delivery time: 7-15 business days (varies by location).
• Tracking details will be sent via email once your order ships.
• If you haven’t received your order within 30 days, contact us at support@xtekin.com for assistance.

• If you're not satisfied, you can return your order within 30 days of delivery.
• Items must be unused, in original packaging.
• Customers are responsible for return shipping costs.
• To initiate a return, email support@xtekin.com with your order details.
• Refunds will be processed within 5-7 business days after receiving your return.

Need help? Contact us anytime at support@xtekin.com! 🚀